In a system with multiple sinks, the default sink may not always be
the once currently being used. It is more useful to control the
currently active sink rather than an unused one.
This patch does not make any difference if the system only uses the
default sink.
Signed-off-by: Roosembert Palacios <roosemberth@posteo.ch>
Whenever the network module is configured with both "format" and
"format-$state" and when the module use "format-$state" once, it
override the value that was saved from "format".
For example, if both "format" and "format-disconnect" are configured,
and only those, as soon as the module show information about a
disconnected interface, it will keep showing the format for
disconnected, even if the interface is connected again later.
Fix that by always setting a value to default_format_ in update() and
thus use the intended default format when needed.
Fixes#1129
When an interface's state is change to "down", all the route
associated with it are deleted without an RTM_DELROUTE event.
So when this happen, reset the module to start looking for a new
external interface / default route.
Fixes#1117
The check to figure out if we have the default route should be after
the for loop that parses the route attributes, to avoid acting on
incomplete information. We are going to use more fields from the
message.
The module doesn't update the `essid_` as soon as a WiFi interface is
connected, but that happens at some point later, depending on
"interval" configuration.
Fix that by rerunning the get WiFi information thread when the
`carrier` state changes. Also, we will clear the state related to WiFi
when the connection is drop to avoid stale information.
Some RTM_NEWLINK messages may not have the IFLA_CARRIER information.
This is the case when a WiFi interface report scan result are
available. `carrier` is used regardless of if it is present in the
message or not. This would result in the interface appearing
"disconnected" in waybar when it isn't.
This patch now check that `carrier` is available before using it.
The same thing could potentially happen to `ifname` so check if it's
set before recording it.
Fixes: c1427ff (network: Handle carrier information)
Fixes#388
IFLA_CARRIER allows to know when a cable is plugged to the Ethernet
card or when the WiFi is connected. If there's no carrier, the
interface will be considered disconnected.
Last part of the rework of handleEvents(), this time we take the
getExternalInterface() function and add it to the handleEvents()
function. That way, waybar can react immediately when a new "external
interface" is available and doesn't need to probe. Also that avoid to
have two different functions consuming from the same socket and we
don't need to recode some of the functions that are already available
via libnl (to send and receive messages).
In order to get the IP address of an interface, we can get the
information out of NEWADDR events without needed to call getifaddrs().
And when now events are expected, we can requests a dump of all
addresses and handle addresses changes the same way via handleEvents()
only.
Instead of using an alternative way to list all links in order to
choose one when an "interface" is in the configuration, we can ask for
a dump of all interface an reuse the handleEvents() function.
This patch also start to rework the handleEvents() function to grab
more information out of each event, like the interface name.
When more than one message is available to read on the ev_sock_
socket, only the first one is read.
Make some changes to be able to read all the messages available by
setting the socket to non-blocking. This way we can detect when
there's nothing left to read and loop back to wait with epoll.
Fix modules starting with no text, but not hidding.
Start with some "text" in the module's label_, update() will then
update it. Since the text should be different, update() will be able
to show or hide the event_box_. This is to work around the case where
the module start with no text, but the the event_box_ is shown.
`format-discharging-full` has been impossible since #923 made it
impossible to be full and discharging at the same time. This should
fix that by only making `format-charging-full` impossible. Whether
or not that should be allowed is a good question, but beyond the
scope of this change.
Fixes#1031
std::regex and std::regex_replace may throw an std::regex_error if the
expression or replacement contain errors.
Log this error and carry on with the next rule, so that the title is
shown even if the config contains errors.
Rewrites window title according to config option "rewrite".
"rewrite" is an object where keys are regular expressions and values are
rewrite rules if the expression matches. Rules may contain references to
captures of the expression. Regex and replacement follow ECMA-script
rules. If no regex matches, the title is left unchanged.
example:
"sway/window": {
"rewrite": {
"(.*) - Mozilla Firefox": " $1",
"(.*) - zsh": " $1",
}
}
Allow the user to show the current volume from MPD status via the
`format` and/or `tooltip-format` configuration options.
The values are provided by libmpdclient and are integers, generally
between 0-100 (without %). Values above 100 are also possible, as mpd
output plugins like `pulse` support volumes above 100%.
Signed-off-by: Sefa Eyeoglu <contact@scrumplex.net>
On some systems (eg: ARM) the supported frequencies of the CPU are not
properly reported by /proc/cpuinfo so if that fails try to retrieve them
from /sys/devices/system/cpu/cpufreq/policy[0-9]/cpuinfo_[max|min]_freq.
Moving rfkill to the main event loop had unexpected side-effects.
Notably, the network module mutex can block all the main thread events
for several seconds while the network worker thread is sleeping.
Instead of waiting for the mutex let's hope that the worker thread
succeeds and schedule timer thread wakeup just in case.
Open rfkill device only once per module.
Remove rfkill threads and use `Glib::signal_io` as a more efficient way
to poll the rfkill device.
Handle runtime errors from rfkill and stop polling of the device instead
of crashing waybar.
Kernel 5.11 added one more field to the `struct rfkill_event` and broke
unnecessarily strict check in `rfkill.cpp`. According to `linux/rfkill.h`,
we must accept events at least as large as v1 event size and should be
prepared to get additional fields at the end of a v1 event structure.
Multiple .done events may arrive in batch. In this case libwayland would
queue xdg_output.destroy and dispatch all pending events, triggering
this callback several times for the same output.
Delete xdg_output pointer immediately on the first event and use the
value as a guard for reentering.
At this point we're not awaiting any protocol events and flushing
wayland queue makes little sense. As #1019 shows, it may be even harmful
as an extra roundtrip could process wl_output disappearance and delete
output object right from under our code.
Ignore any further xdg_output events. Name and description are constant
for the lifetime of wl_output in xdg-output-unstable-v1 version 2 and we
don't need other properties.
Fixes#990.
Add additional fields, namely `source_volume` and `source_desc`
Add `tooltip-format`, reverting to default behavior if not specified
Add additional CSS classes, namely `sink-muted` and `source-muted`
Destroy request is not specified for foreign toplevel manager and it
does not prevent the compositor from sending more events.
Libwayland would ignore events to a destroyed objects, but that could
indirectly cause a gap in the sequence of new object ids and trigger
error condition in the library.
With this commit waybar sends a `stop` request to notify the compositor
about the destruction of a toplevel manager. That fixes abnormal
termination of the bar with following errors:
```
(waybar:11791): Gdk-DEBUG: 20:04:19.778: not a valid new object id (4278190088), message toplevel(n)
Gdk-Message: 20:04:19.778: Error reading events from display: Invalid argument
```
This error occurs because of an incorrect assumption that the size of
the list of nodes that contains the focused window is the number of
windows in a workspace.
The windows in a workspace are stored as a tree by Sway, rather than a
list, so the number of windows has to be found by counting the leaves of
a workspace tree.
GDK Wayland backend can emit two events for mouse scroll: one is a
GDK_SCROLL_SMOOTH and the other one is an emulated scroll event with
direction. We only receive emulated events on a window, thus it is not
possible to handle these in a module and stop propagation.
Ignoring emulated events should be safe since those are duplicates of
smooth scroll events anyways.
Fixes#386
Previously we only checked when connecting to the server whether it had
the minimum required version but didn't act accordingly in the various
functions that use the functionality of later versions. If there were a
server in the wild, that actually would not have this functionality,
there would have been a crash. Fix this by checking the version before
using the functionality and gracefully abort it.
There was an update the of the toplevel manager protocol. Unfortunately,
there are no new interesting updates with regard to the taskbar
implementation. Nonetheless, update the protocol xml files to the latest
version so that the implementation is up-to-date.
While being there, also change the debug warning that is shown when
there is a version mismatch between the server and client version of the
protocol.
Speedup battery state update by only updating the battery list when we
get a CREATE/DELETE event in the directory or whenever we do a full
refresh on the interval.
There was one uninitialized value warning and two mismatched-sign
compare warnings. They both appear valid, the first occurring when MPD's
"format-stopped" contains {songPosition} or {queueLength} and the second
occurring when the clock's "timezones" array is more than 2 billion
items long (not likely, I admit). Fix both issues.
This is very useful when writing CSS that affects more than just a
single widget. Pass `-l debug` to enable debug logging and show this
information.
Example output:
[2020-11-30 12:38:51.141] [debug] GTK widget tree:
window#waybar.background.bottom.eDP-1.:dir(ltr)
decoration:dir(ltr)
box.horizontal:dir(ltr)
box.horizontal.modules-left:dir(ltr)
widget:dir(ltr)
box#workspaces.horizontal:dir(ltr)
widget:dir(ltr)
label#mode:dir(ltr)
widget:dir(ltr)
label#window:dir(ltr)
box.horizontal.modules-center:dir(ltr)
box.horizontal.modules-right:dir(ltr)
widget:dir(ltr)
box#tray.horizontal:dir(ltr)
widget:dir(ltr)
label#idle_inhibitor:dir(ltr)
widget:dir(ltr)
label#pulseaudio:dir(ltr)
widget:dir(ltr)
label#network:dir(ltr)
widget:dir(ltr)
label#cpu:dir(ltr)
widget:dir(ltr)
label#memory:dir(ltr)
widget:dir(ltr)
label#temperature:dir(ltr)
widget:dir(ltr)
label#backlight:dir(ltr)
widget:dir(ltr)
label#battery:dir(ltr)
widget:dir(ltr)
label#clock:dir(ltr)
full-at was capped at the value instead of allowing the battery to show
100% when you were at the full-at value. Uncapping makes more sense as
it makes the full-at value the new 100% and the scale goes down from
there. Whereas before the battery would stay at the full-at value until
it went down enough which is unrealistic.
Since we're now clamping at 100% and rounding, mark as full at that
point. Some batteries will stay in charging state for a long time while
stuck at the same charge level. Just mark them as full to not be
confusing.
The energy values are all that's needed to calculate the battery state.
Using other values for the total capacity results in broken results in
some cases. This matches the output of TLP and i3status, while also
being more straightforward.
../src/modules/network.cpp:22:6: error: ‘optional’ in namespace ‘std’ does not name a template type
22 | std::optional<unsigned long long> read_netstat(std::string_view category, std::string_view key) {
| ^~~~~~~~
../src/modules/network.cpp:7:1: note: ‘std::optional’ is defined in header ‘<optional>’; did you forget to ‘#include <optional>’?
6 | #include "util/format.hpp"
+++ |+#include <optional>
7 | #ifdef WANT_RFKILL
Invisible bar on a `top` layer would still intercept pointer events and
stop them from reaching windows below. Always changing the layer to
to `bottom` along with making bar invisible would prevent that.
Extract two surface implementations from the bar class: GLSSurfaceImpl
and RawSurfaceImpl. This change allowed to remove _all_ surface type
conditionals and significantly simplify the Bar code.
The change also applies PImpl pattern to the Bar, allowing to remove
some headers and fields from `bar.hpp`.
Previous attempts to use auto exclusive zone from gtk-layer-shell failed
because gls was expecting real booleans (`TRUE`/`FALSE`) as set_anchor
arguments. With that being fixed, gtk_layer_auto_exclusive_zone_enable
makes gls handle everything related to the bar resizing.
The only remaining purpose of onConfigureGLS is to log warnings and bar
size changes; gtk-layer-shell code path no longer needs saved width_ or
height_ values.
It's not allowed to bind to a higher version of a wayland protocol than
supported by the client. Binding wlr-foreign-toplevel-manager-v1 v3 to
a generated code for v2 causes errors in libwayland due to a missing
handler for `zwlr_foreign_toplevel_handle_v1.parent` event.
- Add elapsedTime and totalTime to tooltip format arguments
- Catch format exceptions and print error
- Copy mpd connection error message before it gets freed
- Update display after connection to mpd was lost
Read `layer`, `exclusive`, `passthrough` into a special mode "default".
Drop `overlay` layer hacks, as it's easier to use `"mode": "overlay"`
for the same result.
Use `mode` (`waybar::Bar::setMode`) as a shorthand to configure bar
visibility, layer, exclusive zones and input event handling in the same
way as `swaybar` does.
See `sway-bar(5)` for a description of available modes.
- Add MPD module option `password`, and document it.
- Add logic to send the password, directly after connecting to
MPD.
Fixes: #576
Signed-off-by: Joseph Benden <joe@benden.us>
Fix MPD connection issues by converting/rewriting module into a
state-machine driven system. It is fully single-threaded and uses
events for transitioning between states. It supports all features
and functionality of the previous MPD module.
Signed-off-by: Joseph Benden <joe@benden.us>
Fix MPD connection issues by converting/rewriting module into a
state-machine driven system. It is fully single-threaded and uses
events for transitioning between states. It supports all features
and functionality of the previous MPD module.
Signed-off-by: Joseph Benden <joe@benden.us>
Michael Swiger
Grant Moyer
Lars Christensen
Alex
Roosembert Palacios
Patrick Nicolas
dmitry
tiosgz
John Helmert III
Oskar Carl
Anthony PERARD
Maxim Baz
Amanieu d'Antras
Aleksei Bavshin
Yonatan Avhar
Max1Truc
Patrick Hilhorst
Gabe Gorelick
David96
Matthias Richter
Sefa Eyeoglu
jgmdev
Petri Lehtinen
nullobsi
Antonin Reitz
Genesis
Andy Russell
Thomas Sarboni
Martin Pittermann
Kamus Hadenes
Ocisra
ocisra
Marek Černoch
sjtio
Johannes Christenson
dorgnarg
Andreas Backx
Andrea Scarpino
Harit Kapadia
Till Smejkal
Pedro Côrte-Real
Thomas Hebb
Daniel De Graaf
Arnaud Vallette d'Osia
Jordan Leppert
Laurent Arnoud
Flakebi
nikto_b
Joseph Benden
Ole Martin Handeland
Christoffer Noerbjerg
nikto_b
Érico Rolim
Minijackson
lrhel
Thorben Günther